Martel-electronics DTM995 Manuel d'utilisateur télécharger pdf

DIMENSIONS

All dimensions in mm (inches)

19mm (0.75“) Digit Height

Cold Junction Compensation

Simple Connection

LED Backlighting

DTM 995 LCD Type K Thermocouple Indicator

CALIBRATION

1. Place thermocouple at 0°C and adjust OFFSET to

2. Place thermocouple at known reference

temperature, eg. 100°C and adjust CAL

to read 100.

3. Repeat steps 1 and 2 until there are no more

adjustments of CAL and OFFSET required to

give desired readings.

In room temperature application adjust CAL to give the

same reading as a known temperature reference.

This meter will give a direct reading in °C from a K type (chromel-alumel) thermocouple sensor. The circuit uses a converter/amplifier

which has Cold Junction Compensation. Calibration is by two 20-turn cermet potentiometers which allow sensitive adjustment of the

instrument. The meter can also operate without a thermocouple to read room temperature. The meter is housed in a robust carrier,

which can be bolted in place or panel mounted using the low profile bezel, window and clips provided. The meter can also be backlit for

use in poor visibility.

Specification Min. Typ. Max. Unit

Accuracy (overall error) *** 1 % (±1 count)

Thermocouple measurement range

-50 +600 °C

-58 +1112 °F

Power supply voltage (V+ to V-)** 7.5 9.0 24 V

Operating temperature range * 0 50 °C

Temperature stability 0.05 °C/°C

Supply current 3.5 mA

Supply current with backlighting 55 mA

Stock Number

Standard Meter DTM 995

CONNECTOR SOURCING GUIDE

Screw Terminals - No Connector RequiredMETHOD

ON-BOARD SOLDER LINKS

* Module temperature

*** To ensure maximum accuracy, re-calibrate periodically

5V supply option available - Contact Sales for details

REAR

VIEW

T- (blue)

T+ (brown)

V-

LP-

V+

LP+

CAL

OFFSET

61.5 (2.42)

51.0 (2.01)

Ø5.7

(0.22)

24.5 (0.96)

24.0 (0.94)

39.0 (1.54)

Ø3.0

(0.12)

71.5 (2.81)

76.0 (2.99)

72.5 (2.85)

40.5 (1.59)

44.0 (1.73)

24.0 (0.94)

51.0 (2.01)

Panel cut-out 72 x 40 (2.83 x 1.57)

Maximum panel thickness 3mm (0.12).

a. 1.0 (0.04)

b. 2.0 (0.08)

c. 6.5 (0.26)

d. 11.5 (0.45)

e. 13.0 (0.51)

SAFETY

The user must ensure that the incorporation of the DPM into the user’s equipment conforms to the relevant sections of BS EN 61010 (Safety Requirements

for Electrical Equipment for Measuring, Control and Laboratory Use).

www.lascarelectronics.com

1 2

Résumé du contenu

Page 1 - CONNECTOR SOURCING GUIDE

DIMENSIONSAll dimensions in mm (inches)19mm (0.75“) Digit HeightCold Junction CompensationSimple ConnectionLED BacklightingDTM 995 LCD Type K Thermoco

Page 2 - PANEL FITTING

PIN FUNCTIONSROOM TEMPERATURE METER1. V+ Positive power supply connection.2. V- Negative power supply connection.3. T+ Connection for positive (Ni-CR)

Commentaires sur ces manuels

Pas de commentaire

Martel-electronics DTM995 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Martel-electronics DTM995. Martel Electronics DTM995 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Martel-electronics DTM995